LEKI Code: LESECL12014 mm Section915 mm LengthCarbon BlackSpeed Lock + (SL+)2-Section DesignCarbon2020–2021 Production
A carbon lower section in a 2-section alpine ski pole takes the full force of every pole plant — high-speed impact on hard pack, compression through moguls, and repeated clamping and unclamping as you adjust for changing terrain. At 915 mm and 14 mm diameter in carbon, LESECL120 is the genuine LEKI replacement lower section for the LEKI Peak Vario 3D — a 2-section Speed Lock + adjustable alpine ski pole from the 2020–2021 season, built around a 16/14 mm shaft with an aluminium upper section and carbon lower, Trigger S grip system, and a working adjustment range of 105–135 cm. Manufactured to the original carbon specification, it restores the exact 14 mm diameter, 915 mm length, and tube surface that the Speed Lock + lever assembly depends on for solid clamping and smooth adjustment even in cold and gloved-hand conditions.
► Full Technical Specifications
| Section Position |
Lower — Tip End |
| Section Diameter |
14 mm |
| Section Length |
915 mm |
| Material |
Carbon |
| Finish |
Carbon Black (code 98) |
| Locking System |
Speed Lock + (SL+) — external slim lever, no aluminium clamping piece, silver-coloured dial |
| Construction |
Telescopic (Vario) — 2-section |
| Pole Shaft Profile |
16/14 mm (aluminium upper section 16 mm, carbon lower section 14 mm) |
| Production Season |
2020–2021 |
| LEKI Code |
LESECL120 |
► Compatibility & Fitting Guide
LESECL120 is the correct replacement lower section for the LEKI Peak Vario 3D — a 2-section Speed Lock + adjustable alpine ski pole from the 2020–2021 season with a 16/14 mm shaft, carbon black lower section, and Trigger S grip. The 915 mm section length is the definitive identifier — check the printed measurement on your existing lower section before ordering. Compatible with model code 65067611.
✓ LEKI Peak Vario 3D — 2-section Speed Lock + adjustable alpine ski pole, 2020–2021 production, with 16/14 mm shaft, carbon black lower section, and Trigger S grip system (model code 65067611)
✓ To fit: open the Speed Lock + lever fully, withdraw the worn lower section, insert LESECL120 and slide to approximate mid-position — do not force; close the lever, set your preferred length, and test the hold before use
✓ After fitting, apply firm opposing force between the grip and the basket end — the section must hold without slipping; if it moves, adjust the Speed Lock + tension screw clockwise until the lever locks firmly at a comfortable closing force
✓ The Speed Lock + lever is identified by a slim profile with no aluminium clamping piece between the sections and a silver-coloured round dial — if your lever has a smoke-grey or large transparent dial, your poles use a different Speed Lock variant and a different section code applies
► Not Compatible With
✗ Poles using Speed Lock 1 (SL1) or Speed Lock 2 (SL2) — different lever mechanisms and lower section lengths; the tube diameter may match but the section length and clamping interface differ
✗ Fixed-length ski poles — these have no adjustable lower section; LESECL120 is dimensioned for 2-section telescopic construction and cannot be retrofitted to a one-piece pole
✗ Poles with a 12 mm or 16 mm lower section — the 14 mm diameter is specific to the 16/14 mm shaft profile; a different diameter section will not seat correctly in the Speed Lock + lever assembly
✗ Poles with a black anodized aluminium lower section — LESECL120 is the carbon black variant; LESECL127 is the black anodized aluminium section for poles built to the same 915 mm length with SL+
BEFORE YOU ORDER — QUICK CHECK
✓ Section length: the printed measurement on your existing lower section must read 915 mm — this is the primary specification and overrides all other checks
✓ Diameter: confirm the lower (tip) end of your section measures 14 mm — if it measures 12 mm or 16 mm, a different LEKI replacement code is required
✓ Locking system: your poles must use Speed Lock + — a slim external lever with a silver-coloured round dial and no aluminium clamping piece visible between the two shaft sections; if the lever has a transparent or smoke-grey dial, a different LEKI lower section code applies
✓ Finish: your existing lower section must be carbon black — if the section is black anodized aluminium rather than carbon, LESECL127 is the correct replacement code for this length and locking system
