LEKI Prestige, Supreme & Supreme Shark Replacement Lower Section
Product code LESECL51 - Black HS
£21.95
Description
LEKI Code: LESECL51 14 mm Lower Section 831 mm Length Black HS SLS (Super Lock System) 16/14 mm Section Production Era: 2011–2014
At 831 mm, this is one of the longest lower sections available in the LEKI SLS spare parts range — a specification that belongs to the Prestige, Supreme, and Supreme Shark pole families, which use an extended lower section geometry to achieve the pole's full working length. Whether the pole is used on extended ridge walks in the Cairngorms or as a fixed-length setup on the Long Mynd, the lower section carries the same ground contact exposure: rock strikes, creek crossings, and the sustained lateral load of uneven paths. When that section fails, this genuine replacement restores the exact 14 mm diameter, 831 mm printed length, and the black HS finish the original was built with. Finished in black HS (colour code 034), this aluminium section is produced from the 2011–2014 era and built around LEKI's SLS (Super Lock System) internal twist-lock mechanism. The SLS expander clamps against the inner wall of the lower section — at 831 mm, the section wall must maintain precise diameter tolerance along its full length for the expander to seat and hold correctly. A genuine LEKI section ensures that tolerance. Sold as a single section.
► Full Technical Specifications
| LEKI Spare Part Code | LESECL51 |
| Article Code | 81 01 03 14 0831 34 |
| Section Position | Lower — tip end |
| Section Diameter | 14 mm |
| Printed Length | 831 mm — check this on your existing section before ordering |
| Section Profile | 16/14 mm |
| Material | Aluminium |
| Finish / Colour Code | Black HS (034) |
| Locking System | SLS (Super Lock System) |
| Construction | Telescopic (Vario) — 3-section |
| Production Era | Approximately 2011–2014. The 831 mm printed length is specific to extended-geometry pole models — verify the printed length on your existing section before ordering. |
| Sold As | Single section |
► Compatible Poles & Fitting Guide
This lower section is confirmed compatible with the following LEKI SLS trekking poles. Always verify the printed length and diameter on your existing lower section before ordering.
✓ Prestige — 6352620, 6372620
✓ Supreme — 6352315, 6352316
✓ Supreme Shark — 6342622
✓ Additional confirmed compatible article codes (model names not established from available sources) — 6332624
✓ Length verification: The 831 mm printed length is among the longest in the SLS range and is specific to extended-geometry models. Measure the printed marking on your existing section before ordering — any other printed length indicates a different spare part is required.
✓ Fitting: Slide the new lower section into the middle section from the tip end. Rotate the SLS collar clockwise until the internal expander grips the section wall firmly. The section must be fully seated before locking — at this length, any misalignment during insertion is more noticeable; ensure the section enters squarely.
✓ Lock tension check: After fitting, apply downward pressure against a firm surface at working height. If the section rotates or slides under load, adjust the SLS tension collar clockwise in small increments and re-test before use.
✓ Not sure? Email photos of the full pole, the damaged section, and any visible article codes to [email protected] so the correct replacement can be confirmed before ordering.
► Not Compatible With
✗ Speed Lock 1 (SL1) and Speed Lock 2 (SL2) poles — external lever clamp systems; entirely different locking architecture and section interface from SLS internal twist-lock poles
✗ Classic Lock (CLA) poles — older external lever system; different clamping mechanism and section tolerances, incompatible with SLS twist-lock architecture
✗ SLS poles with a standard-length lower section — the 831 mm printed length is specific to extended-geometry models; fitting this section to a pole that uses a shorter lower section will leave the pole outside its designed adjustment range
✗ Poles with a different lower section specification — must match 14 mm diameter and 831 mm printed length exactly; incorrect dimensions prevent the SLS mechanism from locking securely
BEFORE YOU ORDER — FOUR-POINT CHECK
✓ Printed length: Must read 831 mm on your existing lower section — this is a long specification; verify the printed marking carefully before ordering
✓ Diameter: Confirm 14 mm lower section diameter — measure with calipers at the widest point
✓ Locking system: Confirm SLS (Super Lock System) — a twist collar with no hinged lever. If your pole has an external lever clamp, this section is not suitable
✓ Construction: 3-section telescopic (Vario) with 16/14 mm section profile — verify the profile and construction type before ordering
✓ Unsure? Email photos of the full pole, the damaged section, and any visible article codes to [email protected] for confirmation before ordering
Trade Mark of Manufacturer: LEKI
Manufacturer & EU Responsible Person: Leki Lenhart GmbH, Karl-Arnold-Stabe 30, 73230 Kirchheim/Teck, Germany
Contact: www.leki.com
