LEKI Cressida Replacement Lower Section
Product code LESECL64 - Nature Anodized
£21.95
Description
LEKI Code: LESECL64 12 mm Lower Section 420 mm Length Nature Anodized Speed Lock 2 (SL2) 14/12 mm Section Production Era: Approximately 2004–2012
This 12 mm lower section is the correct factory replacement for the LEKI Cressida trekking pole, built on the reduced-diameter 14/12 mm Lite geometry. The Cressida used the Speed Lock 2 (SL2) external lever for height adjustment, clamping directly against the outer wall of the 12 mm section. At 12 mm diameter, the Cressida sits in the slimmer Lite geometry designed for lighter loads and smaller users. The nature anodized finish (colour code 036) and 420 mm printed length are the defining specifications for this section. From easy paths through the Yorkshire Dales to family walks across the South Downs, the Cressida was a dependable Lite-geometry SL2 pole in LEKI’s range. When the lower section is bent, cracked, or worn beyond reliable service, this replacement restores the original geometry and SL2 function precisely. The 420 mm printed length and 12 mm diameter are specific to the Cressida — verify both on your existing section before ordering. Sold as a single section.
► Full Technical Specifications
| LEKI Spare Part Code | LESECL64 |
| Article Code | 81 05 11 12 0420 36 |
| Section Position | Lower — tip end |
| Section Diameter | 12 mm |
| Printed Length | 420 mm — check this on your existing section before ordering |
| Section Profile | 14/12 mm |
| Material | Aluminium |
| Finish / Colour Code | Nature Anodized (036) |
| Locking System | Speed Lock 2 (SL2) — external lever; open lever outward to release, close firmly to lock |
| Construction | Telescopic (Vario) — 3-section |
| Production Era | Approximately 2004–2012. The 12 mm diameter and 420 mm printed length are specific to this configuration — verify both on your existing section before ordering. |
| Sold As | Single section |
► Compatible Poles & Fitting Guide
This lower section is confirmed compatible with the following LEKI poles. Always verify the printed length and diameter on your existing lower section before ordering.
✓ Cressida — article codes 6322119, 6322403, 6322911, 6322912, 6492119
✓ Diameter check: This is a 12 mm section. Measure the diameter of your existing lower section with calipers before ordering. A section measuring a different diameter requires a different spare part.
✓ Length verification: The 420 mm printed length is the defining specification — measure the printed marking on your existing lower section, not the physical length. A section showing any other printed length requires a different spare part.
✓ Fitting: Open the Speed Lock 2 lever to release the existing section, then slide it out from the tip end. Insert the new section and close the Speed Lock 2 lever firmly to secure. The lever should close flush with the collar.
✓ Lock engagement: If the lever does not close fully or the section moves under load, tighten the adjuster nut on the clamp collar clockwise in quarter-turn increments until the lever locks securely. Do not overtighten.
✓ Not sure? Email photos of the full pole, the damaged section, and any visible article codes to [email protected] so the correct replacement can be confirmed before ordering.
► Not Compatible With
✗ SL2 poles with a lower section of a different diameter — the lever collar will not seat correctly on a different diameter and the pole will not lock securely
✗ SL2 poles with a lower section of a different printed length — SL2 lower sections of other printed lengths are different spare parts and are not interchangeable
✗ Speed Lock 1 (SL1) poles — earlier external lever generation; SL2 sections are not interchangeable with SL1 lever collars
✗ SLS (Super Lock System) poles — internal twist-lock mechanism; entirely different locking interface from the SL2 external lever system
BEFORE YOU ORDER — FOUR-POINT CHECK
✓ Printed length: Must read 420 mm on your existing lower section — check the printed marking, not a physical measurement
✓ Diameter: Confirm 12 mm lower section diameter — measure with calipers. This is a 14/12 mm profile section
✓ Locking system: Confirm Speed Lock 2 (SL2) — the lever opens outward from a hinged collar. If your pole has an SL1 lever or an SLS internal twist-lock collar, this section is not suitable
✓ Construction: 3-section telescopic (Vario) with 14/12 mm section profile — verify the profile matches before ordering
✓ Unsure? Email photos of the full pole, the damaged section, and any visible article codes to [email protected] for confirmation before ordering
Trade Mark of Manufacturer: LEKI
Manufacturer & EU Responsible Person: Leki Lenhart GmbH, Karl-Arnold-Stabe 30, 73230 Kirchheim/Teck, Germany
Contact: www.leki.com
