LEKI Speed Lock 2 Carbon Replacement Lower Section
Product code LESECL90 - Carbon
£45.95
Description
LEKI Code: LESECL90 14 mm Lower Section 920 mm Length Carbon / Black Speed Lock 2 (SL2) 16/14 mm Section Production Era: Approximately 2013
This 14 mm carbon lower section is the correct factory replacement for the LEKI Speed Lock 2 (SL2) carbon pole configuration specifying a 920 mm printed length. The Speed Lock 2 external lever clamp mechanism releases with a single outward flip of the lever, allowing rapid height adjustment before re-clamping with a firm press — no rotation required. At 920 mm, this is an exceptionally long printed length for a lower section, placing it in a specialist extended-range pole configuration produced from approximately 2013. The carbon construction (colour code 098) and 920 mm printed length together form the complete identifier for this section. Designed for performance-focused walkers and trail athletes who need the full extension range of LEKI’s carbon SL2 construction — from technical approaches in Snowdonia to the long descents of the Pennine Way — the Speed Lock 2 mechanism delivers fast, reliable adjustment in demanding conditions. When the lower section is damaged or the clamp no longer holds under load, this replacement restores the original carbon geometry precisely. Verify the 920 mm printed marking on your existing lower section before ordering. Sold as a single section.
► Full Technical Specifications
| LEKI Spare Part Code | LESECL90 |
| Article Code | 81 05 11 14 0920 98 |
| Section Position | Lower — tip end |
| Section Diameter | 14 mm |
| Printed Length | 920 mm — check this on your existing section before ordering |
| Section Profile | 16/14 mm |
| Material | Carbon |
| Finish / Colour Code | Carbon / Black (098) |
| Locking System | Speed Lock 2 (SL2) — external lever clamp; flip lever outward to release, adjust height, press lever flat to re-clamp; no rotation required |
| Construction | Telescopic (Vario) — 3-section |
| Production Era | Approximately 2013. The 14 mm diameter, 920 mm printed length, and carbon construction are specific to this configuration — verify all three on your existing section before ordering. |
| Sold As | Single section |
► Compatible Poles & Fitting Guide
Compatible pole model names have not been established from available sources for this section. Verify the printed length, material, and locking system on your existing lower section before ordering. If unsure, email [email protected] with photos for confirmation.
✓ Article code check: If the article code on your pole or documentation ends with 14 0920 98, this section is the likely correct replacement — the 920 mm printed length and carbon construction (code 98) are both required matches. Verify by emailing photos to [email protected] before ordering.
✓ Diameter check: This is a 14 mm section in a 16/14 mm profile. Measure the diameter of your existing lower section with calipers before ordering. A section measuring a different diameter requires a different spare part.
✓ Length verification: The 920 mm printed length is the defining specification — measure the printed marking on your existing lower section, not the physical length. A section showing any other printed length requires a different spare part.
✓ Fitting: Open the SL2 lever fully by flipping it outward to release the clamp, then slide out the existing lower section from the tip end. Insert the new section, position it correctly, and press the lever flat against the section until it clamps with firm resistance. Test by applying downward load before use.
✓ Lever engagement: The SL2 lever should close flat with positive resistance. If the lever feels loose or the section slips under load, the SL2 clamp collar may require assessment or replacement.
✓ Not sure? Email photos of the full pole, the damaged section, and any visible article codes to [email protected] so the correct replacement can be confirmed before ordering.
► Not Compatible With
✗ SLS (Super Lock System) poles — internal twist-lock mechanism; entirely different from the SL2 external lever clamp system; sections are not interchangeable
✗ Speed Lock 1 (SL1) poles — earlier lever generation with a different clamp collar geometry; SL1 and SL2 components are not interchangeable
✗ Speed Lock + (SL+) poles — different lever and clamp mechanism; not interchangeable with SL2 components
✗ Poles with a different lower section specification — a different printed length or aluminium construction requires a different spare part; this section is carbon only
BEFORE YOU ORDER — FOUR-POINT CHECK
✓ Printed length: Must read 920 mm on your existing lower section — check the printed marking, not a physical measurement
✓ Material: Confirm carbon construction — this is a carbon section. An aluminium lower section requires a different spare part
✓ Locking system: Confirm Speed Lock 2 (SL2) — the lever flips outward to release with no rotation. SLS twist-lock or SL1 poles require a different section
✓ Construction: 3-section telescopic (Vario) with 16/14 mm section profile — verify the profile matches before ordering
✓ Unsure? Email photos of the full pole, the damaged section, and any visible article codes to [email protected] for confirmation before ordering
Trade Mark of Manufacturer: LEKI
Manufacturer & EU Responsible Person: Leki Lenhart GmbH, Karl-Arnold-Stabe 30, 73230 Kirchheim/Teck, Germany
Contact: www.leki.com
